How To Make A Water Filter Science Project With 2 Easy Methods!

How does contaminated water gets cleaned up? This enjoyable experiment in science makes clean dirty water. 70% of the world’s water is covered. However, only around 3% of drinking water can be used.

While those in the U.S. have hot, potable water from their kitchen sink, the majority of people around the world have very little access to clean drinking water and then have to boil or filter their water. With this simple project, you will teach your students How to make a water filter science project.

How to make a water filter science project: How can you get started

With the aid of recycled materials, you can conveniently create a water filter for children at home. It is better for kids from grades 3 to 6, but it will work for all ages. It will take approximately one hour to create a homemade water filter. The water filter testing will take between an hour to several hours depending on the intensity at which the water drips.

Via the use of natural materials that replicate the Earth’s water cycle, children explore how the infiltration process works and create a working water filter. Not soap! Not bath! You have to have a filter, an instrument that extracts impurities from water, including dirt.

The filter you are trying to make – with an adult’s help – is a wonderful filter, which can help you clean up your act.

Relate water filter: how to make a water filter at home?

Best homemade water filter making: 2 Easy Methods

homemade water filter project

Method-1

Necessary materials

  • 2-litre, empty and sterile plastic bottle
  • Knife  
  • Contaminated water
  • Cup estimation  
  • Paper and Pencil
  • Coffee Filter (Tool, old sock, or paper towel fits, too!) 

Guidelines

  • Step-1: Tell an adult to halve the glass. Then turn over the top half of the bottle and put it in the back. In the top section, you are going to create your filter.
  • Step-2: At the bottom of your filter placed coffee filters
  • Step-3: In the layers, add cotton balls, charcoal, gravy, grit, etc. Just one or more of them can be seen. Tip: Consider what order to add them. Tip: Usually larger filters capture greater impurities.
  • Step-4: Type out which materials you have used for filters and how they have been mounted.
  • Step-5: Remove and weigh your filthy water in a cup.
  • Step-6: Get set for your timer!
  • Step-7: Fill the filter with a cup of polluted water. Start the timer as easily as you start to pour.
  • Step-8: It takes time for all the water to flow through the filter. Then mark down the time it takes.
  • Step-9: Draw the filter content carefully, one layer at a time. What was taken out of the water by each layer?
  • Step-10: Experiment! Experiment! Clean and try again the bottle. In every phase, every time each experiment put the filter materials in a different order. What do you find? What do you find?

Method- 2

Necessary materials

  • Soda or glass of juice
  • Vase or large bottle
  • Tiny stones or gravel
  • Sand Safe
  • Charcoal
  • Cotton balls, coffee filter, or thin fabric
  • Dirt for gardening
  • Water
  • knife or scissors

We also have a detailed review of the best home water filtration system in the case, If you want to check that out.

Guidelines

  • Using scissors or a knife, cut off the base of an old plastic soda or juice bottle.
  • Lower the bottle into the vase, or place the high glass of the cocktail.
  • Set the first layer inside the container with cotton balls, fabric, or a coffee filter. One to two inches thick should be the first sheet.
  • Cover the cotton sheet with an inch of activated charcoal.
  • In the third coat, add roughly two centimeters of gravel or small stones.
  • Clean sand on top of gravel just over 3 or 4 inches.
  • Fill the bottle with gravel as the last coat. Remove from the top of the upside-down bottle around half a dye.
  • To produce dirty water, apply soil to a glass of water.

Checking the Water

  • The water should be checked before and after filtration for this experiment.
  • To start with, ask the child for a theory or an experiment forecast.
  • Glass the kitchen roller with two bottles of water. As a control, the first glass is. The “dirty.” second bottle.
  • Dirty dirty” water for the house’s products. The “dirty” water can contain items like dirt, potting soil, sparkling water, washing machines, kitchen oils, etc., find all over.
  • Test children with a home water test kit, such as the First Warning Drink Water Test Kit, on two glasses of water.

Then What Will Happen Next?

The more steadily, the stronger! When water passes into a filter, the longer it takes, the better it is. Water quickly slips through filters, but larger gunk gets stuck, like mud.

Typically the filters are finer and finer such that they can capture something that was previously overlooked. Enabled charcoal can be close to the end of the waterway since it uses an electrical charge to collect particles that are too small to see.

Learn about the cycle of water

A homemade water filter is basic job kids enjoy. The project not only lets children learn about the water cycle, but it is also a hands-on experiment that can fascinate them with common materials contained in or outside the home.

The Earth filters water naturally when it is absorbed in the soil. As part of the penetration process, the natural soil in soil leaves, insects, and other debris from the water. Unfortunately, freshwater can be polluted and unhealthy to drink due to pollutants such as paddling goods, household pesticides, and fertilizers.

Bottom Line

It will take approximately one hour to create a homemade water filter. The water filter testing will take between an hour to several hours depending on the intensity at which the water drips.

Via the use of natural materials that replicate the Earth’s water cycle, children explore how the infiltration process works and How to make a water filter science project easily.

Leave a Comment